Top 10 typical forklift mishaps ， forklift procedure must take notice of these issues ！.

Do not underestimate the forklift at the office. If the procedure is not good, there will be major mishaps in mins, and there are several crashes involving forklifts.

Case 1: The forklift cargo blocked the chauffeur's sight, and the person in front could not be found, resulting in a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty items, the staff members utilized their body weight as the weight, which nearly triggered casualties.
Situation 3: The width of the forklift cargo exceeds the allowed size of the path and holds on the roadside shelf, which practically causes an accident.
Instance 4: Forklift is speeding up and rolls over during a turn.
Case 5: The forklift vehicle driver did not see the pedestrian, and the pedestrian did not observe the forklift.
Situation 6: The forklift lifts the personnel unlawfully, the forklift motorist does not use the seat belt, the forklift lifter drops and the motorist is crushed when the forklift rolls over.
Instance 7: The forklift motorist did not use a safety belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these issues ：.

Start.
1. Prior to starting, observe the surroundings, and after validating that there are no challenges that hinder the safety and security of driving, honk the horn first and after that start.
2. For lorries with hydraulic (air pressure) brakes, the brake hydraulic stress (air pressure) scale need to be secure before beginning.
3. When the forklift starts with a lots, the chauffeur should initially confirm that the lots is stable and reliable.
4. The begin must be sluggish and steady.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast needs to be tilted backwards. .
2. Do not raise the fork too high when driving. When getting in and leaving the job website or while driving, take care that there will be no barriers in the sky. When the tons is taking a trip, the fork must not be increased too expensive, which will certainly impact the security of the forklift. .
3. After unloading, the fork ought to be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be issued first. High-speed sharp turns are forbidden. High-speed doglegs will cause the car to shed side stability and tip over. .
5. When the forklift is downhill, it is strictly restricted to switch off the fire and slide, and it is forbidden to brake unexpectedly while driving with lots unless there are special situations.
6. When the forklift is running, it needs to comply with the website traffic rules in the factory and must keep a certain security range from the automobile ahead. .
7. When the forklift is running, the lots has to remain in the most affordable placement that does not prevent the driving, and the gantry needs to be effectively slanted back. The lots will not be elevated other than when piling or packing. .
8. The height of the load should not block the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a reduced rate when turning around.
9. It is prohibited to switch on the ramp, nor to drive across the ramp. .
10. The safe driving rate of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a reduced rate when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to base on the fork to hold products and play a balancing duty. .
12. If troubles are discovered, they will be repaired and reported in a prompt fashion, and they will never run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between both forks ought to be readjusted as required to make the tons of the two forks well balanced and not skewed, and one side of the item need to be against the rack. .
2. It is restricted to deal with a solitary fork or make use of a fork top or pull. In unique scenarios, safety indication should be established to remind surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift should be stopped with the brake. .
4. The speed of the car should be slow-moving and stable. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and hurt individuals. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it needs to be noted that the fork pointer should not touch various other goods or items. The lots ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead slightly when the Stand-on Electric Pallet Stacker tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at Electric Forklift Truck for Warehouse high speed and hit difficult things with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the fork, so regarding avoid the collapse of the goods and harm people. .
8. Straining is prohibited, and it is restricted to make use of forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to use the brake inertia to slip, put, round or roll items. .
10. It is not enabled to use forks to choose, transform pallet discharge.

Leaving .
1. It is restricted to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to unload the goods or lower the fork frame.
2. Pull the parking brake handle to dead or depress the parking brake switch.
3. The engine is turned off and the power is cut off. (Except for special situations, such as the chauffeur does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Before and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and cooling water ought to be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are regular.
5. After the forklift is running, the outside leakage should additionally be inspected and the seals ought to be changed in time.

Forklift Safety Operation Specifications.
1. You must examine before leaving the automobile;.
2. When you experience someone before you during driving, you should send out a signal at a distance of 5 m;.
3. The driving speed in the factory does not surpass 5 km/h;.
4. When driving, the nadir of the freight ought to be 0.3 m ~ 0.4 m above the ground;.
5. The transforming need to not be as well sharp to prevent the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and uniform, and no switching on the slope is permitted.
7. Do not drive across the slope. When the gradient is more than 10%, the car should be driven in reverse when going downhill;.
8. When the forklift workers carry the goods and move on, if they encounter huge or heavy products and go to the motorist's line of sight, they must take the turning around exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to straight shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to get the goods.
6. It is not permitted to use braking pressure to expatriation round or easy-to-roll objects.
7. It is not allowed to bring people to work with the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is increased.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the list below conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844